- 您现在的位置：买卖IC网 > Sheet目录1000 > PR22MA11NTZF (Sharp Microelectronics)RELAY SSR 120V 150MA 6-DIP
PR22MA11NTZ Series
PR32MA11NTZ Series
■ Design Considerations
● Recommended Operating Conditions
Parameter
Symbol
Conditions
MIN.
MAX.
Unit
Input
Input signal current at ON state
Input signal current at OFF state
I F (ON)
I F (OFF)
?
?
20
0
25
0.1
mA
mA
Load supply voltage
PR22MA11NTZ
PR32MA11NTZ
V OUT (rms)
?
?
120
240
V
Output
Load supply current
I OUT (rms)
Locate snubber circuit between output terminals
(Cs = 0.01 μ F, Rs = 100 ? )
?
I T (rms) × 80%( ? )
mA
Frequency
Operating temperature
f
T opr
?
?
50
? 20
60
70
Hz
?C
( ? ) See Fig.2 about derating curve (I T (rms) vs. ambient temperature).
● Design guide
In order for the SSR to turn off, the triggering current (I F ) must be 0.1mA or less.
In phase control applications or where the SSR is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
When the input current (I F ) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, V D , increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit values to start with : Cs = 0.01 μ F and Rs = 100 ? . The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenods.
Following the procedure outlined above should provide sufficient results.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main
output triac as possible.
All pins shall be used by soldering on the board. (Socket and others shall not be used.)
● Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
Sheet No.: D4-A00201EN
8
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
PR308S41ESU
RELAY SSR 240VAC 8A ZC 4-SIP
PR308T11ESZ
RELAY SSR 240VAC 8A TRIAC 4-SIP
PR308T21ESZ
RELAY SSR 240VAC 8A ZC 4-SIP
PR31MA11NTZ
RELAY SSR 240VAC .06A TRIAC 6DIP
PR32MA11NTZF
RELAY SSR 240V 150MA 6-DIP
PR33MF11NSZF
RELAY SSR 240VAC .3A 8-DIP
PR33MF51NSZF
RELAY SSR TRIAC OUT 300MA 8-DIP
PR36MF11NSZF
RELAY SSR 240VAC .6A TRIAC 8-DIP
相关代理商/技术参数
PR22MA11NXPF
功能描述:固态继电器-PCB安装 SSR 10mA Ift 400V 150mA non ZC RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT
PR2-2R2-JBW
制造商:RCD Components Inc 功能描述:RESISTOR WIREWOUND 2.2OHM 2W 5% 制造商:RCD Components Inc 功能描述:RESISTOR, WIREWOUND, 2.2 OHM, 2W, 5%, Product Range:RCD - PR Series, Resistance:
PR230
制造商:LEM Holdings SSA 功能描述:PROBE CURRENT CLAMP BNC AC 200A
PR2304PB010
制造商:Hubbell Wiring Device-Kellems 功能描述:20A 4W DBL ENDED CBL, MALE R/A, 10'
PR2304PB015
制造商:Hubbell Wiring Device-Kellems 功能描述:20A 4W DBL ENDED CBL, MALE R/A, 15'
PR-23-1-1000-B-1/8-0600-M8
制造商:Newport Electronics Inc 功能描述:RTD PROBE, PT1000 S/S 0.125X6IN, Accessory Type:Thermocouple Probe, External Dia
PR-23-1-100-A-1/8-0600-M8
制造商:Newport Electronics Inc 功能描述:RTD PROBE, PT100 S/S, 0.125X6IN, Accessory Type:Thermocouple Probe, External Dia
PR231-40-BR-832-T
制造商:MISC. SPCR/STNDF/HND 功能描述: